Randall Supply Home | About Us | Services | Contact Us
     
 
About Randall Supply
Quality Since 1954
Randall Supply Inc. Services
AC - DC Motor Repairs!
Visit The EASA Web Site!
Randall Supply is a
member of the
Electrical Apparatus Service Association
Browning Bearing and Chain
 
 

Thanks for considering Randall Supply for your Electromechanical and Industrial Supply needs. Below is a list and description of our services. Please do not hesitate to contact us for further information and thank you for taking the time to consider Randall Supply.

Preventative Maintenance
  We recommend that your maintenance program includes a periodic check of all critical machines, motors, and pumps. This is an effort to prevent unwanted downtime and curb your repair costs which is an expensive part of your budget. We will access your plant and outline your most critical equipment. This information will be compiled and given to the maintenance director or designated Preventative Maintenance Manager. Recommendations will be made on equipment that is in need of repair so proper downtime scheduling can be made.
As we all know unplanned downtime is critical to your bottom line and our hope, as your Preventative Maintenance Provider, is that your business will continue to run smoothly.
   
Back to Top!
AC Motor Repairs
 

At Randall Supply, Inc., we offer the ability to repair all ranges of electric motors, small or large. Our 20,000 square foot facility is equipped to handle nearly every type of AC motor in your facility.
Our repair operation uses only the best equipment, materials and engineers available. Inspections are thorough and periodic and every job is documented and stored both electronically and in hard copy. Materials used in the repair process are as follows:

  • Class H ISP Magnet Wire
  • NMN Slot Insulation Paper
  • Nomex Phase Cloth on all Rewinds
  • EPDM lead wire rated at 250 degrees
  • Premium Quality Motor Grade Bearings
  • 100% solids Resin, Polyester, Epoxy

Our testing procedures ensure that you are getting the quality repair you deserve. Test panels range from 30 - 2300 VAC for running at rated volts. Load-testing is also available up to 600HP.

   
Back to Top!
DC Motor Repairs
 

Your DC motor is in good hands with Randall Supply, Inc., as we are capable of repairing a wide variety of DC motors. DC motors are inspected thoroughly and tested for insulation integrity, contamination, and moisture which can shorten the life of a DC motor when they are not monitored and maintained. Routine maintenance programs can cut unnecessary repair costs to a minimum. Your DC motor will under go specific tests to determine its insulation quality. As mentioned in the AC motor repair section above, we use only the best materials in our repair process. By using the latest in equipment and tools our trained technicians deliver the most economic and effective repair process in the industry. A series of tests and inspections will be performed and documented on all DC motors such as:

  • Meg Testing
  • Ground Testing
  • Brush Tension/Brush Wear
  • Commutator Symmetric's
  • Load Testing

Before your motor is returned, you can rest assured, that it has been completely and thoroughly tested to ensure smooth operation and maximum life.

   
Back to Top!
Mechanical Repairs:
 

Here at Randall Supply, Inc., we offer our mechanical services with the assurance of satisfying your every need. Our mechanical services include the repair of gear drives, clutch drives, hoist repairs and general mechanical repairs. Our parts department and inventory allows prompt and cost effective repairs. An extensive library of resources are on hand for reference on most major lines. We take pride in getting your parts fast when it really counts. All gear drive parts are inspected thoroughly in our machine shop where we check for gear wear, shaft run out, seal damage and lubrication. Your gear drives, clutch drives and hoists are tested to factory specifications to ensure the highest quality of repair.

   
Back to Top!
Machine Shop
  Our fully equipped machine shop stands ready to service your needs whether it be lathe turning, milling, sawing, CNC, or welding. Our lathe capacity ranges from 4" x 36" to 34" x 17', CNC lathe 15"x 50". A complete inventory of 1/2" to 6" bar stock ensures the quickest turn around times possible. We are capable of turning or boring a wide range of parts. Our trained mechanist are ready to tackle your most needed orders and parts.
 
Back to Top!
Transport Fleet
  Our fleet consists of a variety of vehicles ranging from 1/2 ton to 10 ton capacity. Having the proper vehicle to transport your machinery is a valuable tool.